How to Develop Black-and-White Film at Home, Step by Step
By the Contact Sheet Maker team · · 7 min read
To develop black-and-white film at home, load the exposed film onto a reel inside a light-tight developing tank in total darkness, then, with the lights on, pour in developer for the time your film's datasheet gives at your solution temperature, followed by stop bath, fixer, a thorough wash and a final rinse in wetting agent before hanging the film to dry. As an example, Kodak's datasheet for Tri-X 400 gives 6¾ minutes in D-76 developer at 68°F (20°C) in a small tank. Times differ for every film and developer, so check the datasheet for yours. The wet steps take under an hour, and you only need darkness while you load the tank.
What you need
Equipment
- A developing tank with reels. Kodak's small-tank instructions are written for 8- or 16-ounce tanks.
- A completely dark space for loading: a light-tight changing bag, or a room you can black out completely.
- A cassette opener for 35mm film, plus scissors.
- A thermometer, measuring graduates and a timer with a clear seconds display.
- Labeled storage bottles, film clips (one of them weighted) and negative filing sheets.
- Gloves, eye protection and an apron.
Chemicals
- Developer, such as Kodak D-76 or XTOL, or another maker's equivalent.
- Stop bath. Kodak's Indicator Stop Bath is non-hardening and contains an indicator that signals when it is exhausted.
- Fixer, such as Kodak Fixer or Kodak Rapid Fixer.
- Wetting agent, such as Kodak Photo-Flo or Ilford Ilfotol.
- Hypo clearing agent (optional), which Kodak says helps remove fixer and shortens wash times.
Safety first
Ilford says photographic chemicals are not hazardous when used correctly, and recommends gloves, eye protection and an apron or overall whenever you handle or mix them. It also says to keep food and kitchen utensils away from your chemicals, never store chemicals in soft drink bottles, label every container and keep everything out of reach of children.
Read each product's safety data sheet. Ilford's US sheet for Ilfosol 3 developer, for example, warns that it causes serious eye irritation and says to dispose of it according to local, state or national rules, so check those before pouring anything down the drain.
Step 1: Load the film onto the reel in total darkness
Kodak's instruction is simple: handle unprocessed film in total darkness, because even a safelight will affect the result. If you use a room, Ilford suggests sitting in it for five minutes with the lights off to check that it really is light-tight.
- Make sure the reel is completely dry, then set out the tank, reel, lid, scissors, cassette opener and film so you can find them by touch.
- In complete darkness, open the film cassette or unroll the film from its backing paper.
- Cut off the narrow leader so the end of the film is square.
- Feed the film onto the reel, touching only the edges, so that no turn of film touches another.
- Cut the film free from the spool, place the reel in the tank and close the lid securely.
Once the lid is on, the film is sealed in a light-tight container, so Ilford says you can switch the lights back on. Ilford calls loading often the hardest part, and a badly loaded film develops unevenly, so practice in daylight with an old film first, then with your eyes closed.
Step 2: Prepare the chemicals and check the temperature
Mix each chemical according to its package instructions. In Kodak's tables, "1:1" means one part stock solution to one part water.
Temperature sets the development time. Ilford calls 20°C (68°F) the standard processing temperature; Kodak lists developer times from 65 to 75°F (18 to 24°C) and specifies its stop, fix and wash steps across the same range. Ilford says those solutions should be within 5°C (9°F) of the developer. Measure the developer right before you pour it.
Step 3: Develop
Development times for Tri-X 400 in a small tank
Kodak's starting points for Tri-X 400 shot at its box speed, with agitation at 30-second intervals:
| Developer | 65°F (18°C) | 68°F (20°C) | 70°F (21°C) | 72°F (22°C) | 75°F (24°C) |
|---|---|---|---|---|---|
| D-76 | 8 min | 6¾ min | 6¼ min | 5½ min | 4¾ min |
| D-76 (1:1) | 10¾ min | 9¾ min | 9 min | 8½ min | 7¾ min |
| XTOL | 8 min | 7 min | 6¼ min | 5¾ min | 4¾ min |
| XTOL (1:1) | 10 min | 9 min | 8½ min | 8 min | 7¼ min |
Kodak notes that tank times under 5 minutes may give uneven results, a good reason to work at 68°F or use a diluted developer. These are starting points; Kodak recommends testing to find the best time for your setup.
How to agitate
Kodak's small-tank agitation, with Ilford's pouring tips:
- Pour the developer in smoothly and quickly, close the tank and start the timer when you finish pouring.
- Firmly tap the tank on the work surface to dislodge air bubbles.
- Agitate with 5 to 7 inversion cycles in about 5 seconds, extending your arm and twisting your wrist 180 degrees.
- Repeat that agitation every 30 seconds.
- Start pouring the developer out about 15 seconds before the time is up, as Ilford suggests, so the tank is empty on time.
Step 4: Stop
Fill the tank with stop bath and agitate. Kodak gives 30 seconds in Kodak Indicator Stop Bath.
Step 5: Fix
Pour in the fixer and agitate frequently. Kodak gives 5 to 10 minutes for Kodak Fixer and 2 to 4 minutes for Kodak Rapid Fixer. Fixer can be stored and reused (Ilford says so of its Rapid Fixer); check the package for capacity. Once the film is fixed, Ilford says you can take the lid off the tank.
Step 6: Wash
HARMAN, Ilford's maker, warns that fixer left in film can degrade the image over time. Kodak gives two wash options:
- Running water for 20 to 30 minutes, or
- A 30-second rinse, then hypo clearing agent for 1 to 2 minutes, then 5 minutes of running water.
Ilford also publishes a water-saving method for its films used with non-hardening fixers: fill the tank with water within 5°C (9°F) of your processing temperature and invert it 5 times; drain, refill and invert 10 times; drain, refill and invert 20 times, then drain. Hardening fixers, and some other makers' films and chemistry, can need much longer washing.
Step 7: Wetting agent and drying
Finish with a final rinse in wetting agent. Kodak gives 30 seconds in Photo-Flo and says it reduces water marks and streaks and helps film dry faster and more evenly. Ilford's method adds a few drops of Ilfotol, diluted 1:200, to the last rinse.
Hang the film with a clip at the top and a weighted clip at the bottom, in a still, dust-free place. If you wipe off excess water with a squeegee, Ilford warns that any grit caught in it will scratch the whole film.
When it is dry, check the result. Ilford says the film edges should be clear, with legible frame numbers, and a good negative shows a full range of tones.
What about color film?
Color negative film uses a different process, C-41, with its own chemistry. Kodak makes its Flexicolor chemicals for Process C-41 for its color negative films, such as Portra, Gold and Ultra Max, and for other makers' films. Follow the instructions that come with your C-41 chemistry.
Common mistakes
- Light leaks while loading. Test your changing bag or room before you risk a roll you care about.
- Contaminating the developer. Ilford warns that even a trace of fixer can contaminate developer and ruin your next film. Use a separate, marked container for each solution.
- Skimping on the wash. Leftover fixer shortens the life of your negatives.
- Touching the negatives. Ilford's advice is to handle them by the edges only.
After drying: scan and make a contact sheet
Ilford suggests cutting dry negatives into strips of six and storing them in dated, labeled filing sheets. To see the whole roll at once, scan the strips, then put every frame on one page: Contact Sheet Maker does it in your browser. Drop the scans, sort them by name, add numbers and download a 300 dpi PDF or JPG. The film-style contact sheet page has a darkroom-style layout with a black background and frame numbers. For the format's history, see what a contact sheet is.
FAQ
Do I need a darkroom to develop film?
No. Ilford says any room you can black out will do while you load the tank, or you can use a light-tight changing bag. After that, the rest of the process happens in normal room light.
How long does it take?
With Kodak's Tri-X 400 times at 68°F, the wet steps take roughly 30 to 48 minutes with a running-water wash, or about 16 to 25 minutes with hypo clearing agent. Add time for loading, mixing and drying.
Can I reuse developer?
It depends. Ilford's beginner guide uses its liquid DD-X developer once and discards it, while Kodak offers a replenisher for D-76. Follow the maker's instructions.
Make a contact sheet in your browser
Drop your photos, pick the grid, download PDF or JPG. Free, nothing uploaded.
Sources
- KODAK PROFESSIONAL TRI-X 320 and 400 Films, Technical Data F-4017 (October 2021) — Kodak Alaris (accessed November 12, 2026)
- Chemicals for KODAK PROFESSIONAL Black-and-White Films, Publication E103CF (revised 12/17) — Kodak Alaris (accessed November 12, 2026)
- Washing Photographic Film & Papers: Instructions for Minimum Water Usage — HARMAN technology (Ilford Photo) (accessed November 12, 2026)
- Making Your First Black & White Print (information sheet) — Ilford Photo (accessed November 12, 2026)
- Ilfosol 3 Film Developer (USA/CAN) Safety Data Sheet — HARMAN technology (Ilford Photo) (accessed November 12, 2026)
- Processing Your First Black & White Film, information leaflet (October 2003) — Ilford Photo (copy hosted by UW–Madison Physics) (accessed November 12, 2026)
- FLEXICOLOR Chemicals, Process C-41 — Kodak Alaris (accessed November 12, 2026)